{"product_id":"overcurrent-over-discharge-protector-for-lead-acid-batteries","title":"Overcurrent \/ Over-discharge Protector for Lead Acid Batteries","description":"\u003cp\u003eThe project described here protects and monitors a Lead-Acid battery against too-low battery voltage and over-current conditions. The circuit consists of\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eMAX4373\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003ecurrent-sense amplifier with internal dual comparators and P-channel MOSFET in series with the battery and its load. It works as a normally closed switch which can be opened if the current-sense amplifier and comparators detect either a\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003ehigh load current OR\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003ea\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003elow battery voltage\u003c\/strong\u003e. When over current condition occurs, the comparator latches the output and can be reset by onboard push switch\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eSW1.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe circuit protects a lead-acid battery by disconnecting its load in the presence of excessive current (\u003cstrong\u003emore than 5A\u003c\/strong\u003e), or a low terminal voltage indicating excessive discharge (\u003cstrong\u003e\u0026lt; 10.5V\u003c\/strong\u003e). The battery and load are connected using\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e0.025Ω\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003ecurrent-sense resistors (R1, R3, R4, R7) and P-channel power MOSFET U1. U1 can handle\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e30V\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eof drain-source voltage and continuous current greater than 5A.\u003c\/p\u003e\n\u003cp\u003eIC U3 is a\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003emicropower\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003edevice drawing only\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e50µA\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eof supply current. It contains a dual comparator and a high-side current-sense amplifier whose output current is proportional to the current through (R1+R3+R4+R7). The top comparator (C2) senses battery voltage via R2\/R5, and drives COUT2 low when the voltage falls below 10.5V. That action turns on LED D2, turns off Q1, and allows R6 to turn off U1 by pulling its gate high. Thus, the battery load is removed when the battery voltage is less than\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e10.5V.\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eRecharging the battery turns U1 back on automatically. C2’s internal 1.5% hysteresis prevents output oscillation near the switching threshold. A linear regulator U2 provides a stable 5V for pull-up resistors R9 and R12. It also sources the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e2.5mA\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003erequired for fault indicator LED D2. LED D1 indicates the output power.\u003c\/p\u003e\n\u003cp\u003eThe output of latched comparator C1 is normally low, which turns off Q2 and allows normal operation. When a load current above 5A drives the CIN1, the voltage goes above 0.6V, the open-drain output COUT1 is latched high (open), allowing R9 to pull T2’s gate high. The resulting low on CIN2 drives COUT2 low, disconnecting the load and illuminating LED D2 just as an over-discharge does, except the load remains disconnected until U3’s active-low RESET input (normally pulled high via R12) is pulled to ground via the normally-open pushbutton switch SW1.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eConnections and Other Details\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eCN1: Pin 1 Battery Red Terminal +12V, Pin 2 Battery Black Terminal GND\u003c\/li\u003e\n\u003cli\u003eCN2: Pin 1 + DC Output, Pin 2 GND\u003c\/li\u003e\n\u003cli\u003eD1: Output Power LED\u003c\/li\u003e\n\u003cli\u003eD2: Fault LED Over Voltage OR Over Current\u003c\/li\u003e\n\u003cli\u003eSW1: Reset Switch\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eInput 12V Lead Acid Battery\u003c\/li\u003e\n\u003cli\u003eOutput Load Current up to 5A\u003c\/li\u003e\n\u003cli\u003eLow Battery Threshold 10.5V\u003c\/li\u003e\n\u003cli\u003eOn Board Reset Switch\u003c\/li\u003e\n\u003cli\u003eOn-Board Fault LED\u003c\/li\u003e\n\u003cli\u003eOn-Board Output LED\u003c\/li\u003e\n\u003cli\u003ePCB Dimensions 53.18 x 32.86mm\u003c\/li\u003e\n\u003cli\u003e4 x 3mm Mounting Holes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"dotfry","offers":[{"title":"Default Title","offer_id":47048580825260,"sku":"B103","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0757\/6436\/7532\/files\/B103A.jpg?v=1787650367","url":"https:\/\/dotfry.com\/products\/overcurrent-over-discharge-protector-for-lead-acid-batteries","provider":"dotfry","version":"1.0","type":"link"}