{"product_id":"under-over-voltage-and-current-protection-switch-high-current","title":"Under\/Over Voltage and Current Protection Switch – High Current","description":"\u003cp\u003eThis simple product allows users to design an under-voltage, over-voltage, under-current, and over-current protection switch. It is a very useful system for safeguarding electrical loads against abnormal power or current conditions.\u003c\/p\u003e\n\u003cp\u003eThe project features a relay with\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eoptocoupler\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003einput, a\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003ecurrent-sensing\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003ecircuit based on the\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eLTC6102\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eamplifier, a\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e6 mΩ shunt resistor\u003c\/strong\u003e, and a voltage divider network for voltage feedback. It is primarily designed for low-voltage and high-current applications up to\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e10A,\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003ebut the relay can handle loads up to 30A at supply voltages up to 48 V.\u003c\/p\u003e\n\u003cp\u003eThe system can be easily controlled using an Arduino or other microcontrollers. Voltage and current feedback signals are fed into the microcontroller’s ADC pins for measurement, while the relay can be switched using a\u003cstrong\u003e\u003cspan\u003e \u003c\/span\u003e5 V control signal\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003efrom the processor.\u003c\/p\u003e\n\u003ch3\u003eFeatures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSupply 12V DC Relay Circuit\u003c\/li\u003e\n\u003cli\u003eLoad Supply 5 To 48V, Load Current Up to 10A (Max 12A)\u003c\/li\u003e\n\u003cli\u003eRelay Triger Input 5V 20mA\u003c\/li\u003e\n\u003cli\u003eCurrent Sensor Output 0.2V\/A (10A =2V)\u003c\/li\u003e\n\u003cli\u003eLoad Up to 10Amps (Max12A), Load Supply Up to 48V DC\u003c\/li\u003e\n\u003cli\u003eLoad Power Supply Feedback 4.364 @ 48V, 0.455 @ 5V Supply\u003c\/li\u003e\n\u003cli\u003e4 x 4mm PCB Mounting Holes\u003c\/li\u003e\n\u003cli\u003ePCB Dimensions 56.52 x 45.88mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eOver\/Under Current Switch\u003c\/h3\u003e\n\u003cp\u003eThe LTC6102 current-sense amplifier measures the voltage across the shunt resistor and provides an output voltage proportional to the load current. This output can be read by the microcontroller’s ADC to implement over-current or under-current protection logic. on-board current-sense resistor R5 voltage-drop, provides a precision output voltage proportional to load current. The circuit includes scaling resistors R8 and R11 that program the gain of the circuit to 33.3V\/V. The LTC6102 is powered from the same supply that the sense resistor is connected to and provides a ground referenced output. The LTC6102 can perform current measurements on supplies ranging from 5V to 48V. Since the output voltage is developed as a controlled current through a load resistance, ground loop errors can be eliminated by simply locating the load resistor at the destination point (subsequent signal processing such as A\/D conversion). Remote loading can be evaluated by simply removing the on-board load resistor (R5).\u003c\/p\u003e\n\u003cdiv class=\"simple-alert-boxes sab_info sab_normal\"\u003e\n\u003cstrong\u003eNote:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eThe system is designed for load voltages up to 48 V, ensuring that the ADC feedback voltage remains below 5 V\u003c\/div\u003e\n\u003ch3\u003eOver\/Under Voltage Switch\u003c\/h3\u003e\n\u003cp\u003eA resistor divider network, formed by R5 = 10 kΩ and R10 = 1 kΩ, is used to scale down the load voltage for ADC measurement. This feedback allows the controller to detect both over-voltage and under-voltage conditions. At 48 V input, the divider provides approximately 4.364 V, and at 5 V input, about 0.455 V. These resistor values can be modified to suit different voltage ranges as required by the application.\u003c\/p\u003e\n\u003ch3\u003eOperations\u003c\/h3\u003e\n\u003cp\u003eAn Over\/Under Voltage and Current Protection Switch can be designed using a combination of voltage divider resistors for voltage feedback, the LTC6102 current sense amplifier for current feedback, and a relay for switching the load on or off at preset threshold levels.\u003c\/p\u003e\n\u003cp\u003eThe board can be interfaced with an Arduino or other microcontroller. The voltage and current feedback signals connect to the ADC inputs, while the optocoupler output connects to a digital pin to control the relay and enable or disable the load. Relay Normally open and Normally closed contacts are open can be route through external wring.\u003c\/p\u003e\n\u003ch3\u003eConnections\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eCN1: Pin 1 = VIN 12V DC Relay Power, Pin 2 = Optocoupler Anode, Pin 3 = Optocoupler Cathode, Pin 4 = Current Feedback Output (VO), Pin 5 = Voltage Feedback, Pin 6 = GND\u003c\/li\u003e\n\u003cli\u003eCN2 Relay Contacts: Pin 1 = Relay Normally Closed, Pin 2 = Relay Common. Pin 3 = Normally Open\u003c\/li\u003e\n\u003cli\u003eCN3: Pin 1 = +Load Power Input, Pin 2 = GND\u003c\/li\u003e\n\u003cli\u003eCN4: Pin 1 = + Load Output, Pin 2 = GND\u003c\/li\u003e\n\u003cli\u003eD1: Relay LED\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"dotfry","offers":[{"title":"Default Title","offer_id":47242800070828,"sku":"B144","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0757\/6436\/7532\/files\/B144.jpg?v=1789735190","url":"https:\/\/dotfry.com\/products\/under-over-voltage-and-current-protection-switch-high-current","provider":"dotfry","version":"1.0","type":"link"}