Isolated Undervoltage and Overvoltage Detection Module
This high-speed, isolated Undervoltage and Overvoltage detection project is implemented with a dual isolated window comparator with an adjustable threshold (AMC23C14). This circuit is designed for industrial field-supply applications where the controller side must detect whether the remote module supply voltage is in a valid range.
The AMC23C14 has open-drain outputs that are pulled up to VCC, and are driven low when the input voltage exceeds the threshold voltage of each comparator. In these measurements, OUT1 (trace 3) transitions low if Vsupply exceeds 28.8V, and OUT2 transitions low if Vsupply exceeds 20.8V. Component variations and the comparator hysteresis can affect the trip thresholds, but in this case, the trip point is within less than 1% of the desired values. The voltage thresholds vary slightly if Vsupply is rising or falling. The second waveform depicts this with OUT1 triggering at 28.6V instead of 28.8V.
U1 (CRE1S0505SC) is an isolated DC-DC converter that provides 5V to the input side circuitry. The module can be powered from input side power, using R1 1K SMD size 0805 and Zener diode 27V 1W SMD. Do not install U1 in this case, the output side requires separate 2.7V to 5.5V VCC.
Over Current and Short Circuit Application
The project is designed for Under/Over voltage detection. However, the project also has provisions to be used for over-current and short-circuit detection. Read the datasheet of the chip for more info. Do not install R3, R6, and R7, Install R10 = 10mOhms SMD size 2512, solder jumper J1 under the PCB. This configuration will help you to detect over current and short circuit across the shunt resistor R10.
Features
- Power Supply 5V DC
- Input Signal 24V
- Over Voltage Level 28.8V
- Under Voltage Level 20.4V
- Output 1 and Output 2 Normally High, Low when Over/Under Condition Occurs
- Transient Response Time 390ns
- Trip threshold error: ±1% (max) at 250 mV
- Open-drain outputs with Pull Resistors
- Dual window comparator: – Window comparator 1: ±20-mV to ±300-mV adjustable threshold
- Window comparator 2: ±300-mV fixed threshold
- 7000-VPK reinforced isolation per DIN EN IEC 60747-17 (VDE 0884-17)
- 5000-VRMS isolation for 1 minute per UL1577
- 5 mm Mounting Hole
- PCB Dimensions 42.23 x 19.05mm
Share
This high-speed, isolated Undervoltage and Overvoltage detection project is implemented with a dual isolated window comparator with an adjustable threshold (AMC23C14). This circuit is designed for industrial field-supply applications where the controller side must detect whether the remote module supply voltage is in a valid range.
The AMC23C14 has open-drain outputs that are pulled up to VCC, and are driven low when the input voltage exceeds the threshold voltage of each comparator. In these measurements, OUT1 (trace 3) transitions low if Vsupply exceeds 28.8V, and OUT2 transitions low if Vsupply exceeds 20.8V. Component variations and the comparator hysteresis can affect the trip thresholds, but in this case, the trip point is within less than 1% of the desired values. The voltage thresholds vary slightly if Vsupply is rising or falling. The second waveform depicts this with OUT1 triggering at 28.6V instead of 28.8V.
U1 (CRE1S0505SC) is an isolated DC-DC converter that provides 5V to the input side circuitry. The module can be powered from input side power, using R1 1K SMD size 0805 and Zener diode 27V 1W SMD. Do not install U1 in this case, the output side requires separate 2.7V to 5.5V VCC.
Over Current and Short Circuit Application
The project is designed for Under/Over voltage detection. However, the project also has provisions to be used for over-current and short-circuit detection. Read the datasheet of the chip for more info. Do not install R3, R6, and R7, Install R10 = 10mOhms SMD size 2512, solder jumper J1 under the PCB. This configuration will help you to detect over current and short circuit across the shunt resistor R10.
Features
- Power Supply 5V DC
- Input Signal 24V
- Over Voltage Level 28.8V
- Under Voltage Level 20.4V
- Output 1 and Output 2 Normally High, Low when Over/Under Condition Occurs
- Transient Response Time 390ns
- Trip threshold error: ±1% (max) at 250 mV
- Open-drain outputs with Pull Resistors
- Dual window comparator: – Window comparator 1: ±20-mV to ±300-mV adjustable threshold
- Window comparator 2: ±300-mV fixed threshold
- 7000-VPK reinforced isolation per DIN EN IEC 60747-17 (VDE 0884-17)
- 5000-VRMS isolation for 1 minute per UL1577
- 5 mm Mounting Hole
- PCB Dimensions 42.23 x 19.05mm
Dotfry has partnered with reputed logistic partners for our logistic services, to ensure that all our products reach you in the best of conditions with no damages. We ensure you that we use packaging materials of the best quality, which is sourced from reliable vendors, and ensure thorough testing of package worthiness before using them for shipping and delivery of our products.
Related Products
